Best Skates for Razer Viper V4 Pro + Installation Guide

Sten @ THREEPOINTZERO
Sten @ THREEPOINTZEROReview Writer · Mouse skate opinions
Underside of a Razer Viper V4 Pro with Glacier Skates, the Glacier Skates pack and the PRO Grips pack

Glacier Skates for the Razer Viper V4 Pro, with PRO Grips for the Viper V3 Pro & V4 Pro.

Razer lists the Viper V4 Pro at 49 g in black and 50 g in white, with 100% PTFE feet and a symmetrical, right-handed shape made for claw and fingertip grips. On a mouse that light, the skates underneath decide a lot of how it starts, moves and stops on the pad.

Razer Viper V4 Pro wireless gaming mouse in black, side view

Razer Viper V4 Pro. Image: Razer.

The stock feet are good out of the box, but every skate wears. When the glide starts to feel scratchy, slower or uneven, it is time for a fresh set. Here is what we at THREEPOINTZERO recommend for the Viper V4 Pro, and how to fit it.

Our pick: Glacier Skates for the Razer Viper V4 Pro

Glacier Skates are 100% PTFE with polished, rounded edges, cut for the Viper V4 Pro's own layout: a front skate, a rear skate and a ring around the sensor. Each piece lines up with where the stock feet sat. On a cloth pad, Glacier gives you a smooth start for micro-adjustments and a predictable stop after flicks.

PTFE or glass on the Viper V4 Pro?

Our model-specific glass Crystal Skates are made for Logitech mice, so there is no full-size glass set for the Viper V4 Pro. If you want a glass feel, Crystal Skates Universal Dots fit any mouse, the V4 Pro included. Place them evenly around the original skate areas so the mouse sits level. For most players we still recommend Glacier: it fits the V4 Pro exactly and feels controlled on cloth.

On a glass mousepad, skip glass skates and full-size PTFE skates, as both wear down the pad. See Best Mouse Skates for Glass Mousepads.

Installation guide: Glacier Skates on the Razer Viper V4 Pro

Underside of a Razer Viper V4 Pro with Glacier Skates, next to the pack

The Viper V4 Pro set: front skate, rear skate and sensor ring.

What you need

  • Glacier Skates for the Razer Viper V4 Pro
  • Isopropyl alcohol and a lint-free cloth (the box includes two alcohol pads)
  • A fingernail, a plastic pry tool or tweezers

Step by step

  1. Switch the mouse off. Turn off the Viper V4 Pro and unplug the cable, so nothing clicks or moves while you work on the base.
  2. Remove the stock feet. Lift an edge of the front foot, the rear foot and the sensor ring with a fingernail or plastic tool, and peel them off slowly. Remove every layer until you see the plastic of the mouse. Take care around the sensor and the Power/DPI button.
  3. Clean the base. Wipe the recesses with isopropyl alcohol to remove leftover adhesive, dust and oil. Let the base dry completely, since a clean surface is what makes the new adhesive hold.
  4. Start with the sensor ring. Peel the ring from its backing by the edges, without touching the adhesive. Center it around the sensor so it does not cover the lens.
  5. Align the front and rear skates. Line each skate up with its recess before it touches the mouse. The Glacier set follows the V4 Pro's original layout, so each piece drops into place.
  6. Press and hold. Press each skate down firmly for around 30 seconds, then run your finger along the edges so the whole skate sits flat. If there is a protective film on top, remove it now.
  7. Let it settle and break in. Put the mouse on your pad and check that it sits flat without rocking. Give the adhesive time to settle before a long session, do a few minutes of slow circular swipes, and play a few sessions before you change your sensitivity.

Common mistakes

  • Leaving a layer of the stock feet on the base
  • Installing on a dirty or greasy base
  • Touching the adhesive with your fingers
  • Using a set made for another mouse, such as the Viper V3 Pro

Want to see it done? Our step-by-step guide to installing mouse skates includes an installation video.

PRO Grips for the Viper V3 Pro & V4 Pro

Razer gives the Viper V4 Pro a smooth-touch finish. In long or warm sessions, a little extra grip helps. Our PRO Grips are pre-cut to fit the Razer Viper V3 Pro and the Razer Viper V4 Pro equally well, with a textured surface that reduces slip for fingertip, claw and palm grips. Clean the sides with isopropyl alcohol first, just like the base.

Glacier Skates for other Razer mice

Have another Razer mouse on the desk? Every Glacier set is cut for one exact model, so pick the one that matches yours.

FAQ

Do Viper V3 Pro skates fit the Viper V4 Pro?

Choose the set made for your exact model. We make separate Glacier Skates for the Viper V3 Pro and the Viper V4 Pro.

Do the PRO Grips fit the Viper V4 Pro?

Yes. PRO Grips - Razer Viper V3 Pro & V4 Pro fit both mice equally well.

How long does installation take?

Usually about five minutes, including cleaning the base.

Can I reuse the stock feet after removing them?

We do not recommend it. Peeling bends the skate and weakens the adhesive.

Do I need new skates on a brand-new Viper V4 Pro?

No. Upgrade when the stock feet feel worn, or when you want a different glide.

Related guides