PS5 Controller Grips: How I Set Up PRO Grips on My DualSense

Sten @ THREEPOINTZERO
Sten @ THREEPOINTZEROReview Writer · Grips & setup
PS5 DualSense controller from above with PRO Grips Universal: long rectangles on the handle fronts, hexagons on the D-pad and face buttons, round dots under the handle

Long rectangles on the handle fronts, hexagons on the buttons. Photo: THREEPOINTZERO

I put PRO Grips on my PS5 DualSense ahead of GTA VI, and a few people asked exactly which pieces went where. Here's how I placed them for my grip. Use it as a starting point, then find your own contact points.

Short answer: my PS5 controller grips setup

  • Grips: PRO Grips Universal, a pre-cut sheet of black TPU grips with mixed shapes.
  • Front of the handles: a long rectangle on each, where my palms press.
  • Back of the handles: a long rectangle and a small square on one side, small strips and round dots on the other, where my fingers rest.
  • Buttons: small hexagons on top of the D-pad and face buttons for my thumbs.
  • Left free: triggers' moving edges, sticks, the gaps around buttons, touchpad, speaker and mic holes, light bar and USB-C port.

Why put grips on a controller at all?

The DualSense is a great controller, but its shell is smooth plastic. In a long session your hands get warm, sometimes a bit sweaty, and the controller starts to slide around in your palms. You compensate by squeezing harder, and after a few hours that's what makes your hands tired.

Grips put texture exactly where your skin touches the controller. You can hold it more loosely and it still stays put. With GTA VI coming up, and plenty of long evenings planned, that was reason enough for me.

What's on the PRO Grips Universal sheet

Back of the PRO Grips Universal pack showing the pre-cut sheet layout: hexagons, squares, round dots, small strips and long rectangles

The back of the pack shows the pre-cut sheet: hexagons, squares, round dots, small strips and long rectangles. Photo: THREEPOINTZERO

PRO Grips Universal is one pre-cut sheet in black TPU, made to fit anything rather than one specific model. It's designed in Sweden, and the mix of shapes is the whole point: hexagons, small squares, round dots, short strips and long rectangles. On a mouse you use them on the sides and buttons. On a controller, the same shapes map surprisingly well onto the handles.

My grip, and why that decides the placement

I hold the DualSense in a relaxed, palm-style grip: the handles rest in my palms, my thumbs work the sticks and buttons, my index fingers sit on the triggers, and my other fingers wrap around the back of the handles. So the contact surfaces on my controller are the front of the handles, the back of the handles under my fingers, and the tops of the buttons under my thumbs. That's exactly where the grips went.

Piece by piece: where I put each grip

  1. Long rectangles on the front of the handles. This is where my palms press when I hold the controller. A long rectangle follows the shape of the handle without wrapping over a tight curve.
  2. A long rectangle and a small square on the back of one handle. The rectangle runs down the back of the handle where my fingers wrap around. The small square sits higher up, just below the trigger, where my finger rests between presses.
  3. Small strips and round dots on the back of the other handle. Two small strips under the trigger area, and round dots further down where my fingertips land. Smaller pieces suit the rounder part of the handle better than one big piece would.
  4. Hexagons on the D-pad and face buttons. The small hexagons sit on top of each button, inside the button's edge, so my thumbs get a bit of texture. I checked that every button still presses and springs back freely before I was happy.
Back of a PS5 DualSense controller with PRO Grips Universal: a long rectangle and a small square on one handle, small strips and round dots on the other

The back: a long rectangle and a small square on one handle, small strips and round dots on the other. Photo: THREEPOINTZERO

How to adapt the setup to your own grip

Your hands aren't mine, so don't copy my layout piece for piece. Copy the method.

  • Palm-style hold: if the handles sit deep in your palms like mine, start with long rectangles on the front and back of the handles.
  • Claw-ish hold: if you hold the controller more with your fingertips and keep your palms off the handles, smaller pieces like dots, squares and strips where your fingertips land usually make more sense.
  • Find your contact surfaces: hold the controller the way you actually play, for a minute, and notice where your skin touches. Those spots are where grip helps.
  • Test-fit with the backing on: hold a piece in place without peeling it, grip the controller again, and adjust until it sits where your hand naturally lands.
  • Keep these free: the triggers' moving edges, the sticks and the gaps around them, the edges and gaps around buttons, the touchpad, the speaker and microphone holes, the light bar and the USB-C port.

Prep: clean before you stick

Grips stick best to clean, dry plastic. Wipe the handles and the back of the shell to remove grease and dust, and let everything dry fully. Do it at room temperature, with clean hands, and press each piece down firmly for a few seconds, smoothing from the middle outwards.

Removing or repositioning a grip

If a piece ends up in the wrong spot, peel it off slowly from one corner instead of yanking it. Then clean the spot and place a fresh piece from the sheet where it should be. That's another reason to test-fit with the backing on first: it saves pieces.

Ready for GTA VI

This setup is the one I'll use on launch night. If you want the bigger picture, including why our old group of friends has waited so long for this game, read Ready for GTA VI: How I Put PRO Grips on My PS5 Controller.

FAQ

Do PRO Grips Universal fit the PS5 DualSense?

Yes. There's no DualSense-specific sheet, but the Universal sheet has a mix of pre-cut shapes that you can place on the handles and buttons where your hands touch the controller.

Where should grips go on a PS5 controller?

On your contact surfaces: usually the front and back of the handles, and the tops of the buttons if you want texture under your thumbs. Keep moving parts, gaps and openings free.

Should I copy your layout exactly?

No. Use it as a starting point, then adjust it to where your own palms and fingers rest.

What are PRO Grips Universal made of?

Black TPU. The pack is a universal pre-cut sheet, designed in Sweden.

Can I use the same sheet on my mouse?

Yes. PRO Grips Universal is made for mice too, which is how most people know it. We also make pre-cut PRO Grips for specific mouse models.

Related guides