Universal Dot Skates Placement Guide: Attack Shark X3, SteelSeries Sensei Pro and More
Glacier Skates Universal Dots and Crystal Skates Universal Dots.
Not every mouse has a model-specific skate set. That is where universal dots come in: you decide exactly where the mouse touches the pad. The trick is placing them so the mouse sits level and glides evenly, without covering anything you still need to reach.
Here is where we at THREEPOINTZERO put dots on four popular mice that we don't make a dedicated set for. The same basics work on almost any other mouse.
Glacier or Crystal dots?
Glacier Skates Universal Dots are 100% PTFE, with 20 dots of 6.6 mm and 20 of 8.0 mm in the pack. You get the classic PTFE feel with a little bite and stopping power, and enough dots for more than one mouse or for trying different layouts.
Glacier Skates Universal Dots: 20 x 6.6 mm and 20 x 8.0 mm, 100% PTFE.
Crystal Skates Universal Dots are glass, with 8 dots of 6.5 mm and 8 of 8.0 mm. They ride on top of a cloth pad's weave, so every movement starts cleaner and the glide stays fast and even. The big dots carry the load at the front, the small ones fill in where space is tight.
Crystal Skates Universal Dots: 8 x 6.5 mm and 8 x 8.0 mm glass dots.
Glacier Skates - Universal Dots - 40pcs (20x Big Dots + 20x Small Dots)
Crystal Skates - Universal Dots - 16pcs (8x Big Dots + 8x Small Dots)
Playing on a glass mousepad? Skip glass dots there. Our Motion Skates Universal 6.5mm Dots are made for glass pads. More in Best Mouse Skates for Glass Mousepads.
Placement basics
- Remove the stock feet completely, then clean the base with isopropyl alcohol and let it dry. Never stack dots on top of old feet.
- Put the dots where the stock feet were. That is where the base is flat and where the mouse was designed to meet the pad.
- Mirror left and right at the same distance from the edge, so the mouse sits level.
- Use the big dots at the front, where your fingers press down the most, and the small dots to fill gaps.
- Keep dots clear of the sensor lens, buttons, switches and any cover that has to open.
- Check the mouse on a hard, flat surface. If it rocks, adjust before the adhesive sets.
Crystal Skates Universal Dots on a Pulsar X2F: one dot in each corner.
Placement by mouse
Attack Shark X3
Attack Shark X3 with Glacier Universal Dots where the stock skates were. Illustration: THREEPOINTZERO, based on an image from Attack Shark.
Attack Shark lists the X3 at about 49 g with a PAW3395 sensor. Underneath sit a wide front skate, a curved rear skate and a ring around the sensor. The DPI and mode buttons sit on either side of the sensor, the 2.4G/Bluetooth switch above it, and the receiver storage just in front of the rear skate.
Peel the front and rear skates and put dots where they were: a big dot in each front corner, plus one in the middle if you want more support, and three dots along the rear arc, one at each end and one in the middle. Keep the dots off the receiver storage so it still opens, and away from the buttons beside the sensor.
SteelSeries Sensei Pro
SteelSeries Sensei Pro with Crystal Universal Dots where the stock feet were. Illustration: THREEPOINTZERO, based on an image from SteelSeries.
SteelSeries lists the Sensei Pro at 53 g, with two swappable batteries. On the underside you find a wide front foot, a ring around the sensor with the Power/DPI button beside it, and a round battery slot at the back, framed by a U-shaped rear foot.
Once the stock feet are off, place your dots over the screw locations. That is what SteelSeries itself recommends for dot feet on the Sensei Pro. Never put a dot on the battery: it twists out every time you swap, so keep the dots on the fixed shell around it, and leave the Power/DPI button free.
Lamzu Maya X
Lamzu Maya X with Crystal Universal Dots where the stock skates were. Illustration: THREEPOINTZERO, based on an image from Lamzu.
The Maya X has an open, frame-style underside. Lamzu fits split front skates, a ring around the sensor, two small round skates on pads beside the sensor and a curved rear skate. A dust cover sticker for the bottom comes in the box.
With so much of the base open, dots can only go on the solid pads: the two front skate areas, the two round pads beside the sensor and the rear arc. The round side pads are made for one dot each. Put one dot in each front area and one at each end of the rear arc, and keep the dots off the dust cover sticker, which is not a firm surface. If you want more support, add one dot on each round side pad.
Pulsar X2 CrazyLight
Pulsar X2 CrazyLight (Mini) with Glacier Universal Dots where the stock skates were. Illustration: THREEPOINTZERO, based on an image from Pulsar.
Pulsar lists the X2 CrazyLight at 35 g. The underside is mostly open: a wide front skate, a wide rear skate, a ring around the sensor and an X-shaped frame in between, with the power switch and DPI button in the open sections.
Put the dots on the front and rear skate areas, the two large flat surfaces. Two or three dots at the front and two or three at the back keep the mouse level. On a mouse this light, fewer dots also means less contact and a faster feel. The thin frame is not a good place for dots.
Installing the dots
Peel each dot by its edge without touching the adhesive, line it up and press it firmly for 10 to 20 seconds. Give the adhesive a little while to set before a long session. Our step-by-step guide to installing mouse skates includes a video.
FAQ
How many dots do I need?
On the mice in this guide, four to six dots is usually enough. What matters is that the original skate areas are covered evenly, so the mouse sits level.
Should I keep the stock sensor ring?
You can. A sensor ring adds a contact point right around the sensor, which some players like for stability. If you remove it, keep the dots clear of the lens.
Can I mix big and small dots?
Yes. Big dots at the front carry the most pressure, and small dots fill in at the back or in tight spots. Just mirror them left and right.
Do dot skates work on glass mousepads?
Yes, in the right material. Use Motion Skates Universal 6.5mm Dots on glass pads, not glass dots.
Can I move a dot after placing it?
Right after placing, you can lift it carefully and adjust. Once the adhesive has set, peeling it weakens the adhesive, so use a fresh dot instead.







